Parts

Filter By

Availability

Availability

Price

Price

  • 0 € - 21,040 €

Categories

Categories

Weight

Weight

  • 0 kg - 198 kg

Delivery time shipment Dixerparts

Active filters

  • Availability: Available
  • Categories: Cafe racer parts
Flasher Booster
Quick view

Flasher Booster

39 €
Availability: 20 In Stock
The Flasherbooster is connected between original flasher relay and your aftermarket indicators. It increase the supply voltages from the original flasher relay to 12 Volt and allow you to use your choice of aftermarket flashers at your bike. An integrated loadequalizer with 0,8 Watt load takes care for the correct flasher frequency in the most bikes.
Marker Light X
Quick view

Marker Light X

43 €
Availability: 10 In Stock
You can also remove the marker light function of the BCM module if you wire the Marker Light X between BCM module and the indicators. This eliminate the marker light function of the indicators.
Vari Load
Quick view

Vari Load

82 €
Availability: 7 In Stock
The solution is a digital adjustable load-equalizer with 50 different presets. The Vari Load is connected to your flashers. The load is adjustable via a simple "programming" cable.
Brake 2 Flash
Quick view

Brake 2 Flash

37 €
Availability: 4 In Stock
The programming of a flasher mode is easy and will cost you about 30 seconds without the need to be a software specialist.
Speed 2 Brake
Quick view

Speed 2 Brake

37 €
Availability: 3 In Stock
The Speed 2 Brake is an electronic brakeswitch what hang parallel to one of the original brakeswitches. The Speed 2 Brake have a speed sensor input what check a reduced speed and activate the brake light in case of a negative acceleration. The sensitivity is adjustable by 10 steps.
Easy Keyless RFID
Quick view

Easy Keyless RFID

201 €
Availability: 10 In Stock
The activation of the module is made via a press on a button. Now you have 15 seconds time to put your rfid tag in front of the antenna. A red led on the antenna indicate the waiting state of the module. If the rfid tag is recognized then the led changes to blue color and the power for the bike is switching on. If the rfid tag is not recognized then the module fall back in sleep mode.
Micro Speedo Module
Quick view

Micro Speedo Module

52 €
Availability: 10 In Stock
The speedometer is very easy to use: If the button is pressed and held down when the power supply is switched on, the wheel circumference appears on the display in cm and counts up between 50 cm and 220 cm until the button is released. The 4 LEDs on the outside indicate neutral, high beam, indicators and oil pressure.
Micro Speedo Black
Quick view

Micro Speedo Black

125 €
Availability: 10 In Stock
The speedometer is very easy to use: If the button is pressed and held down when the power supply is switched on, the wheel circumference appears on the display in cm and counts up between 50 cm and 220 cm until the button is released. The 4 LEDs on the outside indicate neutral, high beam, indicators and oil pressure.
Fuel Indicator
Quick view

Fuel Indicator

41 €
Availability: 16 In Stock
The adjustment of the reserve level is easy: Just connect the module, fill the first required amount of gasoline in the tank and hold the green cable for a moment to ground / Minus. Now the module have store the first value. Then fill the next gasoline level in the tank and repeat the procedure and the module have stored the second fuel level.
Minimal Indicator
Quick view

Minimal Indicator

41 €
Availability: 14 In Stock
The minimal indicator is a small microcontroller module and a 3 color led. The controller drives the different colors of the led and allows to indicate all necessary functions of your bike with just one led. Even 2 or 3 events at the same time can be indicated easily. The small dimensions of the module allows the implementation in the head light or even in the handle bar. You can indicate the foll
Speedsensor
Quick view

Speedsensor

23 €
Availability: 10 In Stock
Care must be taken to ensure the correct position and alignment of the magnet during installation. The integrated LED helps to ensure correct alignment.
Touch 2 Switch
Quick view

Touch 2 Switch

44 €
Availability: 10 In Stock
You can use the module also as a standard headlight relay. Just wire the 2 thin input cables together to one push button. The first press on the push button will switch on output 1 (low beam). Every further press on the button toggle the 2 outputs.
Skrzynka bezpiecznikowa
Quick view

Skrzynka bezpiecznikowa

125 €
Availability: 10 In Stock
Skrzynka bezpiecznikowa z 6 wyjściami zabezpieczonymi elektronicznie. 4 wyjścia ciągłe + 2 przełączane przyciskami. Ochrona przed niedoładowaniem akumulatora.
Mini Safety Box
Quick view

Mini Safety Box

43 €
Availability: 10 In Stock
The safety module check the 2 inputs for the neutral and sidestand switch and enables the start output when the neutral switch is closed, i.e. no gear is selected. The sidestand switch is also be checked. The ignition is switched off as long as a gear is engaged and the sidestand switch is open.
OV Filter
Quick view

OV Filter

22 €
Availability: 10 In Stock
- The ignition produces approx. 20000 - 30000 volts, which means that narrow needle pulses of up to 100 volts or more can be measured on the cables. These overvoltages are often sufficient to destroy parts of the electronics after some time.
Overvoltage Indicator
Quick view

Overvoltage Indicator

43 €
Availability: 10 In Stock
As soon as an on-board voltage of 15.1 volts is exceeded for longer than 2 seconds, a warning flasher function is activated via the two blinker outputs and the additional LED output is switched on. In most cases, it is then sufficient to switch off the engine immediately to prevent major damage.
Harness Kit
Quick view

Harness Kit

41 €
Availability: 9 In Stock
This cable kit allow you a fast and accurate build of your own bike harness. A 6 wire shielded cable allow a fast connection from the handle bar switches to your electronic box. The set comes with 30 cm shrink tube, 8 x 2 cm lettered shrink tube and 30 cable ties in 2 different sizes.